Відео

@FTT143 Awesome! I'm glad you enjoyed it!

@benkanobe7500 Everything Ford related in my videos the parts are purchased from Just8ns. com

@@Jason1Pa Thank you for the wonderful how to video as my tractor is leaking in that exact spot and I see so many others doing the same. On a chance, I tried Just8ns before getting this and they did not list the seal by that number but one digit higher. So I purchased two and in the notes explained I did not find the pitman arm steering shaft seal when I searched but found the one I purchased and if it wasn't correct to please advise me. They are good folks so I suspect they will fix it if I made a mistake. Thanks again and I look forward to more videos from you!

@benkanobe7500 Number:8N3591A should be what you are needing for the seal. If any questions I'd call Derek at Just8ns and ask just to be safe.

@delgriffith1 I don't have any hands on experience with the 860 front ends,but looking on the parts diagram it appears that I don't see any spacers listed which seems rather odd. On the 8N it does call for one spacer then a washer/spacer. I added more cause there was enough slop. I jacked up the front high and rocked the front end up and down and there was no binding. You do need some play for front to back movement, but it's not much. I try to keep the strain off of the radius arms where they insert into the socket near where you feet go.

@@Jason1Pa Makes sense that it wouldn't need a lot of play back and forth to accommodate radius arm swing. The full inch of slop concerns me on my 860. Tempting to put in spacers but at the same time that was the design it seems.

@delgriffith1 Yeah I wish I could offer more help or even look at another one but I don't know anyone that has one. It just doesn't seem right to have that movement.

Glad you like them!

Thanks Steve!! I really want to get back into making some more videos just haven't found a project worth filming. Fingers crossed that will change. Tomorrow I'm heading out to the Northeast John Deere Expo out in Lancaster Ohio. I'll definitely be looking at the crawlers differently now!🤣

Awesome! Have a safe and fun trip... and YES! Please make more videos! Just one walking around that show would be great!

I'm sorry it took so long to get back to you. UA-cam sometimes doesn't notify me when I get a message. The seal gets pressed in the whole way.

I don't have a in depth video unfortunately however here are a couple things. You can check. Grab the PTO shaft (tractor off of course and override clutch off) and see if there is any in and out movement. There really shouldn't be any. If there is there could be a bad snap ring,bearing, etc, damaged causing that slop and creating it to jump out of gear. There is also a small spring and ball (detent ball) in the bearing coupler. That is what your PTO lever hooks up too. If that spring or ball is damaged it will be weak and cause it to jump out of gear. Here is a video of the bearing coupler if your not familiar. Fast forward to the 16:40 mark. ua-cam.com/video/19yITWEWcbk/v-deo.htmlsi=zJNPUu4OmXx1F_Vd

It's unlikely you will find a nut that size a fine tread at a hardware store. I searched through some parts places and to my surprise I don't see new ones. Your best bet is to contact someone that is parting out a 8n to get you some.

Good to hear! Thanks for watching!

Thanks!! Yes they like to get out boogie down the road!

Thanks for watching!! You can email me at jbeluschok@yahoo.com with questions.

I'm sorry I just noticed your reply. Did you get it going?

I don't like how the hoods look after that. Unless it's a 60hp one and the hood doesn't need altered

Not on a 8n

@@Jason1Pa ok thanks. Any that style tractor would probably do. Can you tell me on an 8n should the peddle travel all the way down when pressed down? It’s stopping right after the free play. Just bam that’s it. About half way down. Thanks

@moparornocar3764 Yes it should go all the way down to the running board. If not it almost sounds like your pressure plate is stuck

As I split it again the clutch plate had slipped a little & wouldn’t let the shaft into the pilot because I tried the alignment tool and it wouldn’t slide in. Next time I tightened the pressure plate evenly and made sure the tool would slide all along through the process. So it is back in the pilot now everything looks good peddle goes down a lot further. I guess it’s in the adjustment now. Going try and adjust it tomorrow.

Well I split it again ,three times. This time I’m going to adjust the fingers on the pp. they aren’t being pressed. Seems it isn’t touching the fingers. I’m gona try and tighten them down some to pull the fingers up. Do you know of an easy way to do this , some say 060 not sure where or what to measure. Thanks again.

🤣😂😅 Sometimes you have no choice. Just hope that you don't have a stubborn one.

Thanks your welcome!

20 Ton

You are absolutely correct. At the time of this video I was not aware of this until 4 years later. As you said it's not in the directions. Fortunately. In my opinion the cheap square coils we have available today are pretty weak compared to the round oil filled coils. In my opinion they don't produce enough juice to create the electromagnetic pulse that could destroy the module. I have since replaced all the plug wires on all my Fords just to be safe, but I had several hours on the old copper wires with no issues.

Thanks Will!!

Sorry for the late reply. Sometimes UA-cam doesn't notify me until later that someone posted a comment. This debate comes up often and I agree the directions need to be better. I currently have all 3 of my Fords having the red wire to the top of the coil. Only one of them needed a extra resistor and I have it right into the coil wire and I haven't had any issues. Some say you need to take that red wire from the module and run it straight to the ignition. All I can say is I've never done it and never had a failure.

Yes I do use AVS. Hope this helps you on your repair. If you need help just ask

Thanks George!!

Where are you looking at? Just8ns and Dennis Carpenter are at 289 last I checked. Still cheaper then getting them fixed at a local shop. Last shop I went to said at least 600

@@Jason1Pa yeah I got a new one from Just8ns for the 289 plus shipping.

If it is a 54 it would be known as a model NAA . The Golden Jubilee is a NAA but in 1953 (Fords 50th Anniversary) the NAA is referred to a Golden Jubilee. The only thing different about a 1953 is the emblem that says Golden Jubilee. They are a big improvement over the 8N. First is the overhead valve engine, better hydraulics ,etc.

Harbor Freight has them.

Awesome! Thank you for the compliments! Sometimes I get told I talk to much,but I like to explain things the best I can. I could go on and on,but realize I'll lose people's attention. Unfortunately this day in age people just want a quick answer and nothing else.

I've personally never done it,but I've heard of others do it. However I would expect if they are that worn I'd bet all the other important parts are worn-out beyond repair. Like the output shaft and counter shaft. At that point I'd call the whole thing junk

Hi! Yes this question comes up often. Some things to consider are 1) The hole you would need to drill in the tractor to have access to the plug of the Sherman would need to be fairly large to make sure the oil that's being drained exits completely or it could touch the flywheel and get flung all over the clutch. 2) drilling yet another hole even larger then the one for the shifter lever could possibly have a effect on the strength of the casting. 3) You could put a pipe up in there and have it exit the bottom with a cap on it BUT with the tractor so low to the ground it wouldn't take much to break the pipe off one something. The Sherman doesn't really hold that much oil. Even if that oil is nasty it would be diluted fairly good in the fresh 5 gallons of the main transmission. Another thing is if you'd drain the Sherman empty there is no way to add new oil to it. Oil would need to work its way in there with the oil slinger and that could take a while of driving for that to happen. The Sherman would be turning for a while with little to no oil for a while.

@@Jason1Pa Dumb me...

@@benkanobe7500 The only way to know is to ask. Thanks for watching.

Yes. I have another ford with brand new 12.4x28 on it. Sometimes I wished they were not on there. Pros and cons to it.

That's awesome!! It's so hard to find any old tractor these days that are not worn-out. I leave my Sherman in Standard drive. Only use High to go down the road in 4th. To me the regular gearing is fine other then reverse. Even with the Sherman in low it still doesn't slow it down enough. The Sherman is a good conversation piece, but I'd never invest in another one again.

It's not easy. You have to break off rivets on the gear end. Then you have double nuts that need to come off in the splines side. Why do you want to remove it? Unless the gear is totally trashed or bearing is bad let it be. Some people will even get a whole other housing with one in it already and place.

@@Jason1Pa thanks. I am restoring the tractor and painting everything. I wanted to take everything out of the housing and get it dipped in acid. The animation from Just8ns makes it look like it just bolts in.

@jjay718 No unfortunately it doesn't just bolt in. If you look at that metal piece that directs the oil it is riveted in

@@Jason1Pa I dont want to take that piece out that directs oil. Someone said you can bolt a slide hammer to the front of the pinion shaft where it is threaded. Sucks to take it down this far and not be able to remove the pinion.

@jjay718 That I don't know. If I remember correctly that piece needs to come off. There is like a plate that holds that bearing in place on that end. My memory is a little fuzzy plus I've never taken one out. I just remember guys choosing to swap out the rears simply to avoid that repair. There has to be a reason. I'm curious let me know what you find out.

It's not too bad. Heat is your friend or shop press will get it done too

I guess because I didn't change it.🤣 However pointed side facing radiator.

Everything (all parts) were purchased from Just8ns .com

If all my wiring is current and good, can I just change the points to the EI?

@fuesselfc Yes. However you need to test the coil for resistance to see if you need a extra resistor or not.

Ok, I know I currently have a 12v setup, ballast resistor back of dash, and no additional resistor in line

@fuesselfc So you will want to do a ohms test on your coil. If you are not in the resistance of 3.0 to 3.5 I'd highly recommend adding one of those simple white ceramic resistors in the wire that goes to the coil.

Simply look at the input shaft of the Sherman and count the splines. For a N series and NAA /Jubilee you need 10 splines to fit. If it is 15 splines it won't. Those are for the newer 100 series tractors.

@@Jason1Pa just to clarify. It has 10 spline input. The man I got it from said it came off a 9n with a 3 speed. And mine is a golden jubilee with a 4 speed. Thanks again for sharing your knowledge!

@jessieharris8204 OK sounds good!! Are you sure it is a combo transmission with Standard, High, and Low? They will fit a 9N,but it's not as common to have those in a 9N or 2N simply they were not available at the time when the 9N/2Ns were being produced. If it is a combo it just means someone put it in that 9N way later in life. If the shifting lever is curved like the one in the video then you for sure have a combo. If the lever is straight you have a step up transmission.

@Jason1Pa I'm not home to double check. But I might have my son make a video of it and send it. I think it's freedom eagle TV is the channel name. Thank you again!

I only get Ford parts from Just8ns or Dennis Carpenter

Thanks

Awesome good luck!! I have way better detailed videos on repairs of the N series tractors on my channel. Unfortunately I didn't do a step by step video on this repair.

@@Jason1Pa I have mine down to just the trans and rear axle housing now. I have the hydraulics out of it but I want to pull the axle housings next and the rear diff like you did to clean everything. How hard is it to get the diff out? do you have to worry about preload on the diff itself when putting it back together? I also want to take apart the trans to clean it really good so I will look for a video on that.

@jjay718 The diff pulls right out once you take the left axle housing off. As far as bearing preload no there is no adjustment for the differential BUT buy the proper gaskets so you have the right thickness. A lot of people just use gasket maker. When that housing is bolted down all of it will squeeze out leaving no gap like the gasket does. In my opinion that's too tight on the bearings

Soaking the seals is a preference. If you look into it there are many that do and many that don't. There are even different kinds of rope seals that do and don't recommend soaking. In all honesty if you soak on of them then wipe if off and cut it in half you will see that the oil doesn't even penatrate through to the center only the very outer part. This particular tractor is still going strong and leak free by installing them dry,putting some oil/grease/assembly lube to prevent chafing and has lasted many years now. Thanks for watching

@@Jason1Pa Thanks for the info.

Awesome!! I'm so glad we can use technology like the internet to locate parts easily these days!

Thanks so much William I really appreciate it!! I'm glad you are enjoying them.

@@Jason1Pa Have a happy Easter and next weekend I’m going to West Virginia to meet up with my ford 2N and my grandson Tucker

@williamgawel8467 Happy Easter to you too! Safe travels! Is your grandson named after the car by chance?

@@Jason1Pa no I don’t know where they got that name but that’s the grandson that I have around now he’s only one that I’ll make contact with so he’s going to get this Tractor when we get done and he’s gonna learn how to work on it so have a good day

Thanks William!!

@@Jason1Pa just watching a lot of your old tapes to pass the time till it gets warm enough and I can go up and work on my Ford tractor

When I do rebuild my Ford two and Tractor, I will be passing it along to my grandson along with my tools and also your give him a chance to watch all your whole tapes old tapes. This will be the last one I work on, so it’s time to pass it on thanks again.

@@williamgawel8467 That is wonderful to hear! Thanks for watching. Hope the videos are helpful!

I can't wait for better weather either. We need to dry out too.

@@Jason1Pa same here

Your welcome!! Good luck!

I accidentally did. It's good!🤣

Thanks!!